Temperature control valve system can automatically adjust the outlet temperature or duct temperature water temperature, or adjust the water flow, and heat exchanger units or heat exchanger combination can be made of intelligent heat exchange units or intelligent heat exchangers, the main products The following advantages: 1, the valve controller installation and commissioning is simple, does not require expensive commissioning and on-site programming costs. 2, the controller automatically according to the secondary side of the water temperature, adjust the water flow within the primary valve to achieve comfort, energy saving effect. The outlet temperature of the heat exchanger compensates and varies according to the outdoor temperature. The user feels comfortable during use, avoiding the higher outdoor temperature and the higher the indoor temperature, and the lower the outdoor temperature is, the lower the indoor temperature is. Users in the use of comfortable premise, can save operating costs, reduce operating costs and achieve considerable economic benefits. 3. Depending on the use of the scene, especially unattended workstations, multi-function controller can be used to extend the selection of features to support the pump, flow, pressure and other control, and the operation of the fault alarm. 4. The valve body adopts advanced pressure feedback device, which solves the problem that long plagued the electric control valve due to high pressure drop. Wide range of uses, can be used for chemical, petroleum, metallurgy, electric power and light industry production and automatic control, suitable for air conditioning, refrigeration, ventilation, heating and other heat exchange occasions. 5, electric valve actuator hydraulic control patented technology to achieve high thrust, long life, safety and stability, which can effectively save user investment. 6, Add outdoor temperature sensor, realize outdoor temperature compensation, and save energy and reduce operating costs. The main features of the temperature control valve: 1, all components of the electric temperature control system are imported products, split supply, easy to transport and maintain. 2, electric temperature control valve can accept all kinds of control system output intermittent and continuous control signal, easy system integration. 3, the electric valve body structure using balanced structure, the same output power in the case of electric actuators, it is more applicable than the single-seat direct valve to allow a wider range of pressure. Small size, light weight, easy installation. 4, when the valve is closed or open to large, the limit switch to cut off the power to protect the motor. 5. Electric actuator using permanent magnet synchronous motor, fast response, output power, low power consumption, low noise. Temperature control valve structure: electric temperature control valve structure is divided into two-way valve and three-way valve. By the electric valve and valve actuators, controllers and sensors. 1, the electric valve body and actuator electric proportional valve diameter: DN15-DN150 valve interface for the thread or flange, the pressure is PN10 to PN40, the medium temperature range from up to 350 degrees. 2, temperature controller RWD62 or RWD68 controller, can receive a variety of sensor signals, such as 0-10V, PT100, Ni1000 and so on. The output signal is DC0-10V or digital signal. 3, commonly used sensors Immersion water temperature sensor QAE2120.010 (QAE22A) Use: -30-130 ℃, sensitive components: Ni1000 Connection: 2-wire immersion casing material: stainless steel immersion casing length: 100mm thread connection G1 / 2 Outdoor temperature sensor QAC22 temperature range: -35-50, Ni1000, 2-wire connection. Search Keyword: More Valves Technical Articles Valves Products Selling Leads
Resistance Forming Machine
SF-200 is a Hand belt type resistance Forming Machine which is the best selection for mass production.Easy adjustment,operation and long life.
SF-201 is the same as SF-200,Beside above ,they are Loose Tape resistance Former suitable for vertical or horizontal shaping of resistors and diodes.
SF-202Component bending forming machine is bulk, with resistance and diodes are available.Foot cutting, bending can be strengthened, foot long span can be adjusted.
SF-208FB Axial automatic resistor machine has three Models for Processing Different Type of Packing.
SF-206 The bulk Resistor Former has three models each for both M&C types.The difference are listed as follows:â‘ SF-206-MA;SF-206-CA for loose packed components â‘¡SF-206-MA;SF-206-CB for taped packed components â‘¢SF-206-MA;SF-206-C for using on both taped and loose packed components.
SF-208 Equipment K Type Resistance Molding Machine has three Models for Processing Different Type of Packing.â‘ Loose packed Model(SF-208-FA).â‘¡Taped Model(SF-208-FB).â‘¢ Loose packed/taped combinative Mode(SF-208-F).
SF-206MB The axial lead former m type has three models each for both M&C types.The difference are listed as follows:â‘ SF-206-MA;SF-206-CA for loose packed components â‘¡SF-206-MA;SF-206-CB for taped packed components â‘¢SF-206-MA;SF-206-C for using on both taped and loose packed components.It is also means automatic resistor forming m machine.
Resistance Molding Bending Machine,F Resistor Cutting Machine,Component Cutting Forming Machine,Components Lead Cutting Machines
SINGSUN ELECTRONIC SCIENCE & TECH CO.,LTD , https://www.szsingsunautomatic.com