UV marking machine markable for plastic bottle glass cup pvb board PCB FPC
Â
UV laser marking machine, using the 355nm UV laser research and development and, using three order intracavity frequency doubling technology, into the international advanced technology, high energy ultraviolet photons direct damage many nonmetallic materials surface molecules, molecules from the object, in this way will not produce high quantity of heat, ultraviolet laser gathering spot minima and processing of almost no heat effect, therefore is called cold processing, so it can be used to special material ultra fine marking and engraving.
Â
Â
Properties:
Laser type | ultraviolet green |
 Laser wavelength | 355nm |
Laser power | 3w/5w/7w/10w |
Standard engraving range | 100mm*100mm |
Optional marking range | 50mm*50mm,150mm*150mm, 180mm*180mm |
Engraving speed | less than or equal to 10000mm/s |
Outline dimension (W*D*H) | 68*65*145cm |
Weight: | 120kg |
Power demand | Ac220V + 10%.50Hz-60Hz.5Amp |
Cooling mode | Water Cooling |
Operating temperature: | 10-35 DEGÂ C |
humidity: | 5%-75% (non-condensing) |
Â
Product description:
Working principle and characteristics:
Dapeng laser and UV play labeling machine series products into the international advanced technology, high energy ultraviolet photons direct damage many nonmetallic materials surface molecules, molecules from the object, in this way will not produce high quantity of heat, ultraviolet laser gathering spot minima and processing almost no heat affected, therefore is called cold processing, so it can be used to special material ultra fine marking and engraving.
Â
Product advantage:
1. Short UV laser wave length, smaller focused spot, can realize ultra fine marking;
2. is cold processing, small heat affected zone, avoid damage to materials to be processed, high rate of finished products
3. applicable materials widely, make up the deficiency of the infrared laser processing capacity;
4. using high-speed digital galvanometer marking speed, high efficiency, high precision;
5. without supplies, use cost and maintenance cost is low; the performance is stable, long-term operation.
Â
Industry application:
UV laser light spot is very small, and there is almost no heat affected, so it is called cold processing, which is suitable for special materials, super fine marking and engraving. Mainly used for ultra precision machining of the high-end market, cosmetics, medicines, food and other polymer materials of the surface of the packing bottle marking; flexible PCB board marking, dicing; silicon wafer micro hole, blind hole processing; LCD glass two-dimensional code marking, glassware play standard, metal surface coating removal, plastic buttons, electronic components, communication equipment.
Â
Flexible and convenient operating system:
User friendly operation, equipment operation stability is good; the special control software can be compatible with AutoCAD, CorelDRAW, Photoshop and other softwares output; can realize text symbols, graphics, bar code, two-dimensional code, serial number and so on automatic editing and modification; support PLT, PCX, DXF, BMP, JPG and other file formats can be used directly TTF font; CCD automatic identification tracking and positioning;
Â
Working environment requirements:
1. environmental temperature requirements at 10-35 DEG C, air conditioning requirements;
2. temperature requirements for < 60%. No condensation, should install dehumidifier;
3. power supply requirements: 220V; 50HZ/60HZ;
4. power supply fluctuation: + 15%, grid wires meet international requirements. Area voltage amplitude of 15% or more, should install the electronic type automatic voltage regulator, stabilizer;
5. shall be installed near the equipment without strong electromagnetic interference. Around the installation to avoid a radio transmitter station (or trunk);
6. Foundation: less than 50Um; the amplitude of vibration acceleration: less than 0.05g. Avoid a large number of press and other equipment in the vicinity of the press;
In the equipment space requirements to ensure smokeless clean, avoid metal polishing and grinding dust serious working environment;
7. air pressure: 86-106kpa
In some environment should be installed anti-static floor, strengthen shielding;
Exergy cooling circulating water quality has strict requirements, require the use of pure water, deionized water or distilled water, can not use of water, mineral water, etc. liquid with high metal ion or other minerals.
Marking samples but not limited.
Â
Sheet Metal Stamping And Deep Drawn
Sheet metal stamping and deep drawn are two common manufacturing processes used in the production of metal parts and components.Sheet metal stamping involves the use of a stamping press to shape and cut sheet metal into a desired shape or form. The process involves placing a sheet of metal between two dies, which are then pressed together to create the desired shape. This process is commonly used to create parts for automotive, aerospace, and electronic applications.Deep drawn, on the other hand, is a type of sheet metal stamping that involves the use of a specialized press to create parts with a deep, cylindrical shape. The process involves placing a sheet of metal over a die and then using a punch to push the metal into the die, forming a deep, cylindrical shape. This process is commonly used to create parts for medical, automotive, and aerospace applications.Both sheet metal stamping and deep drawn are highly versatile and cost-effective manufacturing processes that can be used to produce a wide range of metal parts and components. By using these processes, manufacturers can create complex shapes and forms with high precision and accuracy, making them ideal for a variety of industrial applications.
Sheet Metal Stamping And Deep Drawn,Deep Drawn,Sheet Metal Stamping,Sheet Metal Stamping Deep Drawn
Suzhou Remgar Metal Manufacturer Co.,Ltd. , https://www.rmheatsink.com