PVC Edge Banding Tapes Extruder Making Machine Machine

Posted on

Engagement System: Full Intermeshing
Screw Channel Structure: Deep Screw
Exhaust: Exhaust
Automation: Automatic
Computerized: Computerized
Production Name: PVC Edge Banding Extrusion Machine/Making Machine
Second Name: PVC Edge Banding Machine
Edge Banding Width: 10-50mm
Edge Banding Thickness: 0.2-2mm
Extruder Design: Conical Twin Screw Extruder
Mian Motor Power: Siemens 18.5kw
Inverter: ABB
Main Electrical Part: Siemens Schneider
After Sales Service: Engineer Overseas Installation
Trademark: Sino-tech
Transport Package: Wooden Case
Specification: CE, ISO
Origin: China
HS Code: 84772090
PVC edge banding machine/extruder machine

1. Our company is cooperating with many universities to develop the urgently needed plastic machine. It also absorbs advanced technology from abroad to achieve the purpose of supplying complete machine and technology.

2. PVC edge band machine
3. The PVC edgeband Extrusion Line is used for extruding PVC edgeband. The edgeband in the form of roll has its thickness of 0.5-4.0 mm and width of 5-300mm depending on the requirments. Its length is not limited. This product is featured by its good banding effect, easy operation and high utilization rate, therefore it is applicable to mechanical banding of solid furniture, composite doors and WPC doors.
 
Item Technical parameter
I. SJ65/25 Single Screw Extruder
Supplier of electric control cabinet Main transducer and feeder's transducer: Hitachi transducer; Air switch:
Output capacity 80kg/h(approximate)
Inlet wire terminal of power source 3-phase, 4-wire system
Motor power Main motor:AC30kw
Temperature control curve type Temperature fluctuating self-adjustment(PID type)
Temperature control meters, manometers and speedometers RKC(Japan) temperature control system, Xiaogan Wuyue(China) sensor and high quality speedometers respectively.
Pressure display With melt pressure display
Feeder type Vacuum feeder(with drier), with enganced screw feeder
Connection of die head with flange By bolts
The advantages over other companies in this field Good shearing, high output, reasonable design, high accuracy and easy control, high-grade materials and parts with steadfast performance.
   
1. Screw  
Diameter 65mm
LD 25:1
Quantity 1pcs
With gas vent or not With
   
2. Barrel  
Barrel type Integer
Heating method Air cooling unit. Special stainless cover and red copper electricity heater are used on the barrel
Heating zones 7-zone
Total heating power 60kw(approximate)
Temperature range 50~300
Cooling zones 7-zone
Cooling system 7X0.55kw
Cooling medium Air cooling
Screw and barrel manufacturer Zhejiang Machinery Co., Ltd
Quality guarantee Testing block and tested report are available. Guaranteed period is more than 10,000 working hours
Nitrid depth 0.6~0.7mm
3. Driving system and speed reducing system
Main driving motor power 18.5kw
Main motor working method 3-phase asynchronous motor, connected to the gearbox by couple
Main motor rotating speed  
Gearbox type Helical gear, hardened
Gears Carburized and ground; The material is 20CrMoTi
Main motor speed-adjusting method AC transducer
   
II.Haul-off unit
Haul-off speed 20-30m/min(adjustable)
Speed control method Inverter
Motor power 0.75kwX2
   
III. Single disc winder
Winding range 15-25mm
   
IV. Mould 1 set

Any question,please call me. 
MOB&waspp: +8613773240086
 

Waste Rubber Pyrolysis Plant introduction:

Waste Rubber Pyrolysis Plant can refine the waste rubber into fuel oil by pyrolysis process. The final product will be base oil which can be made into diesel and gasoline.


1.Working process Of waste rubber  pyrolysis plant:

First, the raw materials are put into the reactor, and then seal the feeding in door, later start the machine and the reactor will be rotating and heated by coal, natural gas, wood or electricity. When the temperature reaches the degree of 250 to 280, we will get the crude oil, the oil steam will be continuous produced until the temperature reaches 350-460 C; oil steam will flow through oil gas separator, light component will enter the condensers and meanwhile the heavy oil will be discharged automatically into in heavy oil tank. The liquefied part will be condensed as crude oil, and the part which cannot be liquefied will be transferred by the water seal back to the burning chamber to be reused as heating material.

 

 

2. Model of waste rubber Pyrolysis plant:

 

Model

Reactor size

Material

Handling capacity

Weight

Seaworthy packing

LJ-8

2200*6000mm

Q245R boiler steel plate

5 tons

24tons

2*40HQ

LJ-9

2200*6600mm

Q245R boiler steel plate

8tons

26tons

2*40HQ

LJ-10

2600*6600mm

Q245R boiler steel plate

10tons

30tons

1*40FR+1*40HQ


3. Installation: We will be in charge of arranging our engineer to go to your place to guide the installation and train your workers how to operate the pyrolysis plant,and buyer will be in charge of the food, accommodation and round air tickets.

4. Land requirement: 300sq meters(10m*30m)

5. Exporting Experience:

 America:

Brazil, Canada, Colombia, USA,

Middle East:

Dubai, Iran, Jordan, Saudi Arabia, Turkey

Europe:

Albania , Bosnia and Herzegovina

Asia:

Afghanistan, India, Malaysia, Pakistan, Philippines, South Korea, Vietnam, Myanmar

Africa:

Ghana, Mozambique, Zambia

 

 

Waste Rubber Pyrolysis Plant

Waste Rubber Pyrolysis Plant,Tire Pyrolysis Plant,Waste Rubber Pyrolysis Oil Plant,Waste Tire Oil Pyrolysis Plant

Shangqiu Sihai Energy Technology Co., Ltd , https://www.sihaienergy.com