LED advertising car tires can not be ignored:
First, the first LED advertising vehicle tire inflation should pay attention to safety. Always check the air pressure with a barometer to avoid over-inflating and bursting the tires.
Second, after stopping the vehicle, it is necessary to wait for the tire to cool before re-inflating, as the temperature of the tire will increase when the vehicle is driving, which has an impact on the air pressure.
Third, check the valve. If the valve stem and the valve core do not match with each other, there are protruding recesses and other defects, and it is inconvenient to inflate and measure the air pressure.
Fourth, the advertising car should pay attention to clean inflatable. The filled air must not contain moisture and oil to prevent deterioration of the inner tube rubber.
Fifth, when the inflation should not exceed the standard air pressure and then deflate too much, can not be too long after the out inflated and over-inflated, if more than the standard will lead to excessive expansion of the cord, causing its strength to reduce, affect the LED The life of the car tires.
Sixth, LED advertising vehicle tires should be cleaned before filling the dust on the valve, do not loosen the valve core, after the completion of the application of soap bubble water (or saliva) painted on the valve, check whether the leak (if the leak will Produce small bubbles) and tightly seal the valve cap to prevent sediment from entering the interior of the valve.
7. Some advertisement vehicles are equipped with other tires. For example, when the radial tire is inflated, its sinking volume and grounding area are large because of the structure. It is often mistaken for under-inflation and over-inflated; or because it sinks. The amount and the ground contact area are inherently large, and they are mistaken for a sufficient amount when the air pressure is insufficient. Apply a standard barometer to measure. The radial pressure of the radial tires should be 0.5-1.5kg/cm2 higher than that of ordinary tires.
Batch Waste Tyre Pyrolysis Plant
Batch Waste Tyre Pyrolysis Plant
Pyrolysis Plant is used for recycling waste tire, waste plastic, waste rubber to fuel oil. According to the actual situation in every country and district, we developed different models of Batch Pyrolysis Plants for waste tires, rubber and plastic with daily capacity 5 -10 tons.
Flowchat of Batch Waste Tyre Pyrolysis Plant
Advantages of Batch Waste Tyre Pyrolysis Plant
1. Full open door design: Speedy loading in and steel pulling out; Easily cooling down after one batch finished, saving time; No leaking with special high temperature flexible graphite packing.
2. Unique Craft Condensers: High condensing efficiency with more oil output. Good quality oil, longer lifetime, and easy to clean.
3. National Patent Unique Smoke Scrubbers: More efficient removal of the acid gas and dust of the smoke by neutralization, purification and absorption, environmental friendly without pollution.
4. National Patent Carbon Black Discharging System: Speedy fully enclosed Auto-discharging under high temperature, avoiding carbon black pollution, saving time.
5. Automatic Submerged welding technology, ultrasonic nondestructive testing, both manual and the automatic safety devices.
6. Sync Gas Recycling System: Fully burned after recycling and utilization, saving fuel and preventing pollution.
7. Direct Heating System: Enlarging heating square to lengthen the lifespan of the reactor and easy to control the temperature.
8. National Patent, unique heat insulation shell; high efficiency temperature keeping, excellent energy-saving effect.
Technical Parameter of Batch Waste Tyre Pyrolysis Plant
|
NO. |
ITEM |
PROJECT |
|
|
1 |
Equipment Model |
XY-7 |
XY-8 |
|
2 |
Door Model |
Full Open Door |
Full Open Door |
|
3 |
Suitable Raw Materials |
Rubber/Plastic Products |
Rubber/Plastic Products |
|
4 |
Structure |
Horizontal Type Revolves |
Horizontal Type Revolves |
|
5 |
Reactor Size |
Φ2200*6000mm Φ2600*6600mm |
Φ2200*6000mm Φ2600*6600mm |
|
6 |
Capacity for One Batch |
5-6Mt; 8-10Mt |
5-6Mt; 8-10Mt |
|
7 |
Oil Yield of Tires |
40%-45% |
40%-45% |
|
8 |
Work Pressure |
Normal Pressure |
Normal Pressure |
|
9 |
Reactor Rotation Speed |
0.4R/M |
0.4R/M |
|
10 |
Fuels Choice |
Coal, Wood |
Coal, Wood, Gas, Oil |
|
11 |
Power |
18KW/H |
18-25KW/H |
|
12 |
Cooling Method |
Water Cycling |
Water Cycling |
|
13 |
Type of Drive |
External Annular Gear |
External Annular Gear |
|
14 |
Heating Method |
Direct |
Direct |
|
15 |
Type of Installation |
With Foundation |
With Foundation/Integrated Base |
|
16 |
Noise dB(A) |
≦85 |
≦85 |
|
17 |
Operation Mode |
Intermittent Operation |
Intermittent Operation |
|
18 |
Total Weight(MT) |
25-40 |
25-40 |
|
19 |
Installation Space Required |
30m*10m |
30m*10m |
|
20 |
Manpower |
3~4/batch |
3~4/batch |
|
21 |
Shipment |
Ф2200×6000=1*40HC+1*40FR Ф2600×6600=2*40HC+1*40FR |
Ф2200×6000=1*40HC+1*40FR Ф2600×6600=2*40HC+1*40FR |
Batch Waste Tyre Pyrolysis Plant,Waste Tyre Pyrolysis Plant,Rubber Pyrolysis Recycling Plant
Shangqiu Jinpeng Industrial Co., Ltd. , https://www.recyclings.nl