Why is it that summer car maintenance is more important? Because in the hot summer days, the sun's strong exposure to the car will cause damage in many places, there will be danger during the journey, the experts said that in summer car care More important. Here we look at which aspects should be maintained.
First, to prevent spontaneous combustion phenomena. According to the master of the auto repair factory, there are many reasons for the auto-ignition of the car, but the main reason is the oil circuit and the circuit, and then the reason that the car may be damaged during the modification. However, the most common and common phenomenon of spontaneous combustion still occurs in the area of ​​short-circuit of the wire, since the probability of occurrence in this area is over 60%. The aging of the line is the main reason for the short circuit of the wire. When the weather is relatively high, this phenomenon is accelerated more quickly. Another possibility is that the owner himself provides the car with some additional electronic devices, anti-theft devices, high-grade audio, etc. These are things that will increase the load on the car circuit, so it is not recommended to have too many electronic devices.
In order to prevent spontaneous combustion of the car, it is necessary to pay more attention to the observation of the car at ordinary times, such as the issue of maneuvering, circuits, oil lines, etc., to see whether there is aging or oil leakage. Must be equipped with fire extinguishers on the car, lighters, perfumes, air decontamination agents can not be placed in the car, these are flammable after high temperatures.
Second, prevent car tires from sunburn. Summer is the season of high incidence of automobile tire puncture, because the tire is the most direct contact with the high temperature of the ground, and the air temperature will puncture the tire after the inner tire pressure is too high. In the summer tire pressure should be reduced by about 10%, the best way is to add nitrogen in the tire, which is an inert gas, can greatly reduce the probability of puncture. Also observe that cracks in the tires should be repaired or replaced in time.
Third, prevent cars from boiling. When the temperature in the car's water tank is too high in summer, the phenomenon of panning often occurs. If there is a car, you should find a cool place to cool the car, let the engine run at idle speed, and turn on the hood quickly to dissipate heat. Be sure to wait for the temperature to drop. Add water to the tank. You should also pay more attention to observing the instructions on the water temperature table during the summer.
To pay more attention to the above issues in peacetime, observe more, work harder, and there will be no problem with cars.
Process:
The foil roll is introduced into the rubber roller of the feeding device via the decoiling machine and then would in the winding former after passing through the edge of the shearing machine and the roller wheel of the burr pressing device. The inter layer insulation coil is erected in the rear of the coiling optical shaft of the foil winding machine and wound in the winding former after sheared by the trimming roll and the shears blade.
Functional feature:
1. The device adopts and electrical servo deflection correction system to achieve manual/automatic adjustment of the foil position more conveniently and reliably.
2. An advanced electrical control technology of constant tension is adopted to control the tension of the foil and the inter layer insulation, with the features such as quantitive, accurate and convenient control of the tension no mechanical friction. The required tension can be maintained for forward winding, stop and backward winding, ensuring compact coils.
3. The inter layer insulation adopts a cantilever mechanism, convenient for feeding and the mechanism can be pulled out as a whole without guide rails outside the body.
4. Automatic welding mechanism and roll shearing mechanism adopt ball screws and linear guide rails for drive, ensuring the service life and accuracy of the device.
5. This device first adopts the all-in-one sing frame, solving problems such as few coil urns and deflection correction lag.
6. This device is a hi-tech product produced by combining with actual production on the basis of many similar products at home and abroad. The whole machine is controlled via an advanced PLC touch screen, with high automation level and simple and reliable operation, representing higher production level of domestic foil winding machines.
Cnc Winding Machine,Foil Winding Machine,Cnc Wire Winding Machine,Hv Foil Winding Machine
JINAN EURO-ASIA MACHINERY CO., LTD , https://www.euroasiamachine.com