According to the requirements of the Ministry of Commerce, the draft of the industry standard for the “Technical Standards for Scraping Vehicles†drafted by the China Automotive Technology and Research Center was published and publicly solicited for comments. The deadline for comments was May 30, 2014. The proposed technical specification proposes that the comprehensive recovery rate of renewable resources after automobile scrapping and crushing will be no less than 90%.
Breaking technology regulations are becoming clearer
As we all know, scrapped cars contain a lot of harmful substances, such as lead, mercury, cadmium, polybrominated biphenyls and polybrominated diphenyl ethers. These materials are widely used in automotive steel, glass, brake pads, electronic devices, leather, coatings and other components or In the material. "Recycling car recycling is not something anyone can do. Raising the barriers to entry is one of the ways to regulate the industry." Zhao Chao, an industry expert in the automotive recycling industry, told reporters that the proposed technical specification for scrapping car scraps is aimed at raising The entry barrier will guide the end-of-life vehicle recycling enterprises to improve the level of environmental protection operations in the areas of material separation and reuse.
In the future, the automobile scrapping and crushing plant area should not be located in the drinking water source protection zone, the basic farmland protection zone or other areas that require special protection. The working site area is not less than 20,000 square meters, and it is equipped with sewage collection ditch, oil-water separation and other sewage treatment. Device. Through equipment sorting or manual sorting, the remaining materials obtained after scrapping the scrapped car will include reusable materials such as stainless steel, wire, rubber, and plastic.
Standardize the development of the industry in Jiangxi
The scrap car recycling and dismantling industry involves public safety, environmental protection, resource recycling and the healthy and rapid development of the automobile industry. In order to strengthen the management of the scrap car recycling and dismantling industry, in March this year, the Jiangxi Provincial Government issued the "Opinions on Promoting the Standardized Development of the Scrap Automobile Recycling Industry in the Province". "Opinions" plan "By 2020, the province's scrap car recycling and dismantling enterprises will grow to about 32." At the same time, scrapped car recycling and dismantling enterprises should meet the requirements of the commercial department for the unified planning and rational layout of the scrapped car recycling industry. It complies with the relevant laws and regulations and relevant national technical specifications.
Jiangxi Province encourages scrap car recycling and dismantling enterprises to actively improve the scrap car recycling network in the region in line with the principle of close to the convenience, perfect network and orderly competition. Encourage scrapped car recycling and dismantling enterprises to actively carry out on-site services to facilitate car owners to sell scrapped vehicles and handle related procedures. Under the premise that the recycling network in the region is basically perfect, the scrap car recycling and dismantling enterprises that meet the requirements of the relevant national technical regulations may set up recycling outlets within the province according to law.
At the same time, it is expressly required that scrapped automobile recycling and dismantling enterprises shall not entrust other units and individuals that do not have the qualifications for scrapping and recycling of scrapped automobiles to carry out scrapped automobile recycling business. Enterprises shall set up recycling outlets, which shall be reported to the competent commercial departments of the districts and cities where the outlets are located for the record; the collection of recycling outlets shall be set up across the districts and cities, and the competent commercial departments of the districts and cities where the enterprises are located shall be reported for the record; the recycling outlets shall have fixed office premises and enterprise personnel.
There are also regulations on environmental protection. The Opinions require that scrapped vehicle recycling and dismantling enterprises should establish environmental supervision accounts, including the types, weights or quantities and destinations of scrapped motor vehicle dismantling products and other solid or liquid wastes that enterprises cannot handle (non-recyclable) in depth. Information such as the discharge of pollutants during the dismantling process. At the same time, the establishment of dangerous goods management accounts, focusing on the types and quantities of hazardous waste generated after various dismantling, time of storage, storage, disposal and utilization. Regularly report the types, production quantities, storage, disposal and utilization of hazardous wastes in the previous quarter to the environmental protection departments of the districts and cities. Corporate environmental monitoring reports and business records should be kept for at least 3 years.
In addition, Jiangxi Province encourages the scrap car recycling and dismantling enterprise to upgrade and renovate, and plans to cultivate 1~2 regional disposable automobile crushing demonstration centers in the province. It is reported that this favorable policy has attracted and retained a lot of waste recycling giants.
Among them, the “Guangxi Fengcheng Scrap Automobile Recycling Industrial Parkâ€, which is designed to recycle and recycle waste resources and recycle high-tech products, has been designed and put into production. The company plans to scrap the car base in Jiangxi. It will build a recycling, recycling and comprehensive utilization center for scrapping vehicles in the province and the surrounding areas of Jiangxi, providing a model for the company's nationwide scrap car industry layout.
Folding mask machine, also known as Lijin C-type mask machine, is a fully automatic machine used for the production of folding mask bodies. It uses ultrasonic technology to bond 3 to 5 layers of PP non-woven fabric, activated carbon and filter materials, and cut out Folding the mask body can process 3M 9001, 9002 and other mask bodies. According to the different raw materials used, the masks produced can meet different standards such as FFP1, FFP2, N95, etc. The ear straps are elastic non-woven fabrics, which make the wearer`s ears comfortable and stress-free. The mask filter cloth layer has a good filtering effect and perfect It fits the face shape of Asian people and can be used in high-pollution industries such as construction and mining.
Automatic Folding Mask Machine,Folded Face Mask Machine,Automatic Face Folding Machine,High Speed Folding Mask Machine
Broadfair Automation Equipment Co., Ltd. , https://www.broadfairmachine.com