On December 2, General Motors reported that Han Desheng, President and CEO of General Motors Corporation of the United States, resigned. General Motors Chairman Ed Whitacre will temporarily serve as CEO of GM.
It is reported that this is a major adjustment made to management by General Motors after bankruptcy and restructuring. It is also the result of growing disagreement between Henderson and General Motors's board regarding the development strategy of the company.
On Tuesday (December 1st) General Motors held a press conference in Detroit to announce the above news. Whitacre read a short statement at the meeting but did not accept the reporter's question.
Whitacre said that thanks to Han Desheng’s hard work in the past eight months, Han Desheng led GM to experience a major juncture of bankruptcy and restructuring. Whitacre said that the search for long-term successors of Han Desheng will begin immediately.
Maryann Keller, an independent automotive industry analyst in the United States, said: "They seek to restructure General Motors in a completely different way. They hope that the next president of GM can have a completely different perspective."
Han Desheng, 50, was appointed chief executive of General Motors in March this year when the government demanded that his predecessor, Rick Wagoner, resign.
It is reported that after the reorganization of General Motors, Han Desheng formulated a success in reducing costs and streamlining brand strategy. However, Han Desheng has encountered some difficulties in dealing with other brands. When General Motors sells a series of assets such as Saturn, Hummer, and Opel, it can be said that There are twists and turns.
PAG, the second-largest car dealer in the United States, originally planned to acquire the Saturn brand, but announced that it would abandon the acquisition when the transaction should come to an end at the end of September. General Motors's board later decided to phase out the Saturn brand. Last week, Sweden’s Koenigsegg Group also gave up its plan to acquire Saab, causing the Saab brand to face the fate of being shut down.
In addition, GM’s decision to stop selling its Opel plan surprised and surprised the global automotive industry. As we all know, Han Desheng once strongly supported this plan of sale. This is where Han Desheng and the General Motors Board of Directors disagree.
U.S. government officials said that the U.S. government did not step into the GM CEO’s decision to resign. It may take months, not weeks, for GM to find a new CEO.
Function:CJF series lab magnetic stirred autoclave is a stirring and reacting device and this series of stirred reactors has been designed for users who need higher operating pressure.
It is used for kinds of chemical materiasl which are Gas-liquid, liquid-liquid, liquid-solid or gas-liquid-solid three-phase to react and stir fully under the high pressure, vacuum, high temperature, up to strength mass and heat transfer process.
Temperature from Room temp to 350 Degree C
Pressure from 0.1 Mpa to 35Mpa.
Usage and Range
CJF series sealing High Pressure Reactor Autoclave is a stirring and reacting device, which is used for kinds of chemical materiasl which are Gas-liquid, liquid-liquid, liquid-solid or gas-liquid-solid three-phase to react and stir fully under the high pressure, vacuum, high temperature, up to strength mass and heat transfer process.
Notes:
1. Reaction medium should not exceed the kettle of two-thirds surface!
2. At work or at the end, demolition is strictly prohibited! Kettle is strictly prohibited in the case of ultra-pressure, high-temperature work!
3. When cleaning up autoclave, special attention should be paid not to heat water or other liquid spills into the furnace to prevent heating stove burned. If heat jacketed heat-conducting oil, don`t add water or other liquids during add heat conduction. Shall check the oil level of heat-conducting oil from time to time!
4. If internal of insulation shell has abnormal noise during operation, should be shut down, and check the mixing system whether is exception. Periodic checks shaft mixing swing. If the swing is too large, should be timely replacement of bearings or sliding bushings!
Without Lifting High Pressure Reactor
Sealing high pressure reactor autoclave Static sealing high pressure reactor autoclave stainless steel high pressure reactor autoclave factory direct high pressure reactor autoclave Lab high pressure reactor autoclave
Zhengzhou Keda Machinery and Instrument Equipment Co., Ltd , http://www.zzkdrotovapor.com